Oil and Gas

Course catalogue

hits
351
Course code: MUK-168
Course type: E-learning course
Duration: 2 hours
Language: English
Price: GBP 125,-

Course Goal: This course aims to provide learners with an overview of well integrity and its importance in maintaining safe and secure operations

 

Target Audience: All relevant personnel

 

This course contains the following sections:

 

Section 1: Well Integrity Overview

Section 2: Well Categorisation and Well Barriers

Section 3: Well Design and the Cementing Process

Section 4: Human Factors in Well Integrity

Course code: NI-020
Course type: E-learning course
Duration: 30 minutes
Language: Norwegian / english
Price: GBP 40,-

The course covers the following topics:

- What is psychosocial working environment?
- Characteristics of good and poor psychosocial environment
- Roles and responsibilities
- Prevention

At the beginning of the course you can take a pre-test, where you get the opportunity to show your skills. If you pass the pre-test, you do not have to go through the entire course.

Course code: MUK-018
Course type: E-learning course
Duration: 30 minutes
Language: English
Price: GBP 40,-

Course Goal: This course aims to provide all relevant personnel with the knowledge required to understand the hazards and controls associated with the use of abrasive wheels.

Target Audience: This course is aimed towards all personnel who use abrasive wheels in the workplace.

Learning Objectives

LO1 Explain what is meant by the term ‘Abrasive Wheel’
LO2 Explain the legislative requirements for abrasive wheels
LO3 Give examples of different types of abrasive wheels
LO4 Explain how abrasive wheels operate
LO5 Explain the importance of using guards during grinding operations
LO6 Explain the requirements for portable and hand-held grinding machines
LO7 Explain the main hazards of grinding operations
LO8 Give examples of common problems faced when using abrasive wheels
LO9 Explain what the PPE requirements are during grinding operations
LO10 Identify the safety measures that must be in place during grinding operations

Course code: MUK-122
Course type: E-learning course
Duration: 20 minutes
Language: English
Price: GBP 40,-

Course Goal: This course aims to give personnel an introduction to different types of respiratory protection and describe its use in the workplace

 

Learning Objectives:

LO1 Explain what is meant by Respiratory Protective Equipment (RPE)

LO2 Give an overview of the relevant legislation and regulations governing RPE 

LO3 Identify the different types of RPE commonly used in the Oil and Gas Industry 

LO4 Explain the requirements for respirator face fit testing

LO5 Describe the importance of filters when using RPE

LO6 Demonstrate how to correctly select RPE

LO7 Describe the factors to consider when wearing RPE

LO8 Explain the importance of correctly maintaining RPE

LO9 Give an overview of cleaning and storage requirements for RPE

 

Course code: MUK-196
Course type: E-learning course
Duration: 30 minutes
Language: English and Norwegian
Price: GBP 40,-

Course goal: This course aims to increase learners’ awareness of the importance of Personal Protective Equipment (PPE), and outline the legal duties and responsibilities of employers and employees in relation to PPE.

 

Learning Objectives

 

LO1 Define what is meant by Personal Protective Equipment (PPE)

LO2 Identify the different types of PPE 

LO3 Identify typical regulatory requirements associated with PPE

LO4 Describe the Hierarchy of Control measures and the use of PPE in relation to this

LO5 Explain the requirement for assessing the suitability and compatibility of PPE

LO6 Explain the maintenance requirements for PPE

LO7 Describe the duties and responsibilities of employees in relation to PPE

LO8 Explain the importance of PPE-related training, information and instruction 

 

Course code: MTP-061
Course type: E-learning course
Duration: 30 minutes
Language: English, Norwegian
Price: GBP 40,-

The Code of Conduct course provides an overview of the common values that govern responsible corporate practice and personal behaviour in a company. The course will identify the responsibilities of employees and our common responsibilities toward each other in the workplace. You will learn about applicable laws on human rights, equality, discrimination and corruption. During the course, you will be asked to make your own decisions in relevant dilemmas involving sexual harassment, bullying, discrimination and corruption.

Course code: MUK-121
Course type: E-learning course
Duration: 1 hour 30 minutes
Language: English
Price: GBP 80,-

Course Goal: This course aims toprovide learners with an introduction to major accident hazards

 

Learning Objectives

LO1 Explain what is meant by the terms ‘major accident’ and ‘Major Accident Hazard’

LO2 Describe the difference between occupational hazards and Major Accident Hazards

LO3 Give examples of major accidents and recognise why and how they occurred

LO4 Describe how barrier models are used to identify and mitigate risk

LO5 Give examples of systems which can help prevent Major Accident Hazards

LO6 Explain what is meant by a Safety and Environmentally Critical Element 

LO7 Explain the importance of Safety Critical Maintenance

LO8 Explain what is meant by a Safety Critical Task

LO9 Explain how human factors relate to Major Accident Hazards

Course code: RV-COR1
Course type: E-learning course
Duration: 7 Minutes
Language: English
Price: GBP 0,-
Course code: MTP-038
Course type: E-learning course
Duration: 45 minutes
Language: English, Norwegian
Price: GBP 110,-

Insufficient understanding of risk often leads to delayed projects, accidents and other unwanted incidents.
This course provides a basic understanding of what risk is, how it can be managed and how understanding risk helps us make better decisions.

 

Course Content
- What is risk?
- Managing risk
- That we each play a role in preventing things from going wrong
- That actions and decisions may influence the risk to ourselves and others far into the future
- That we perform risk assessments in order to make better decisions when we are unsure

 

Course code: MUK-014
Course type: E-learning course
Duration: 1 hour 30 minutes
Language: English
Price: GBP 100,-

Course goal: This course aims to provide all relevant personnel with an overview of best practices in Mechanical Isolations.

Section 1: Course Overview
Section 2: Introduction to Mechanical Isolations
Section 3: Roles and Responsibilities
Section 4: Safety Critical Manual Valves (SCMVs)
Section 5: Planning Isolations
Section 6: Performing Isolations
Section 7: Isolation Security
Section 8: HP/LP Systems
Section 9: Reinstatement of Plant

Course code: MUK-109
Course type: E-learning course
Duration: 1 hour
Language: English
Price: GBP 80,-

Course Goal: This course aims to provide personnel with an overview of the requirements and operation of a typical permit to work system

 

Target Audience: All relevant personnel

 

Learning Objectives:

LO1 Describe the purpose of a permit to work system and identify when it applies

LO2 Give examples of work which may require a work permit

LO3 Identify the different work permits that are commonly used in the Oil and Gas Industry

LO4 Describe the validity and display requirements for work permits

LO5 Give examples of common additional documentation that may be required to accompany a work permit

LO6 Give an overview of key roles and responsibilities within the permit to work system

LO7 Describe the individual roles and responsibilities of the different personnel involved in the permit to work process

LO8 Explain the purpose of the toolbox talk

LO9 Give an overview of work planning and risk assessment requirements

LO10 Explain the key stages involved in issuing a work permit

LO11 Identify the importance of stopping the job

LO12 Describe what is involved in suspending a work permit

LO13 Outline the requirements for permit renewal

LO14 Describe what is involved in closing a work permit

LO15 Describe shift handover responsibilities

LO16 Outline the work completion requirements

LO17 Identify training and competence requirements

LO18 Identify the main legislative requirements for implementing a permit to work system

Course code: MUK-020
Course type: E-learning course
Duration: 1 hour 30 minutes
Language: English
Price: GBP 80,-

Course goal: This course aims to provide all relevant personnel with a broad overview of common Electrical Safety Rules, and outlines best practice when working with electricity

Target Audience: All personnel working with electricity in the Oil and Gas Industry

Section 1: Importance of Electrical Safety Rules

Section 2: Roles and Responsibilities

Section 3: Planning and Precautions for Electrical Work

Section 4: Standard Procedures for Electrical Work

Section 5: Working Safely when using Specific Electrical Equipment

Course code: KYS-001
Course type: E-learning course
Duration: 3-5 hours
Language: Norwegian
Price: GBP 575,-

The course provides employees who are responsible for drinking water offshore, or tasks associated with this, increased knowledge and understanding to provide good, sufficient and safe drinking water to the staff on board.

Satisfy the requirements for competence in relation to the Norwegian Public Health Institute’s guidelines: “Nok, godt og sikkert drikkevann offshore.”

After the course you should:
- Know about and be able to orient yourself in the relevant regulations with emphasis on the public health department's supervisor “Nok, godt og sikkert drikkevann offshore"
- Understand the distinction between drinking water affect the installation's water system, and people's health
- Understand the purpose of the various laboratory analyzes used to monitor the quality of water
- Know which analyzes offshore employees are responsible for themselves, and what responsibilities they have in connection with the analyzes that must be sent to an accredited laboratory
- Be able to interpret results from laboratory analyzes and know what action offshore staff must implement when results are abnormal and/or critical
- Understand the structure of a drinking water system offshore, and where in the system offshore personnel has responsibility for operation and maintenance

Please note: this course is also available in an English-language version. 

The course is delivered by the accredited laboratory SINTEF NORLAB AS. 

Course code: MUK-107
Course type: E-learning course
Duration: 30 minutes
Language: English
Price: GBP 40,-

Course goal: 
This course aims to provide the knowledge and techniques for carrying out efficient shift handovers

Learning Objectives:
Describe the communication process that takes place during shift handover
Identify common handover failures
Identify the problems that may occur during shift handover
Explain the importance of good shift handovers
Explain the use of shift handover logs
Describe the benefits of site visits
Identify the expectations and responsibilities at shift handover
Describe the shift handover planning process
Summarise the key points of a shift handover

Course code: MTP-062
Course type: E-learning course
Duration: 30 minutes
Language: English, Norwegian
Price: GBP 40,-

This course provides an overview of common corporate sustainability approaches and identifies the social, environmental and corporate governance aspects that should be considered during business operations. The course also identifies the human rights that are at risk of infringement in the work environment, and you will be aware of the global presence of modern-day slavery. During the course, you will be asked to make your own decisions in relevant dilemmas involving environmental criminality, corruption and breaches of labour rights.

Course code: MUK-160
Course type: E-learning course
Duration: 30 minutes
Language: English
Price: GBP 40,-

Course Goal: This course aims to provide an overview of management of change. The course focuses on the steps of the management of change process, the roles and responsibilities of personnel, and the risks involved in change management and their associated control measures.

 

Target Audience: All relevant personnel

 

Learning Objectives:

LO1 Explain why the effective management of change is an essential part of operations in the Oil and Gas Industry

LO2 Define ‘change’

LO3 Describe the key stages in the management of change process

LO4 Identify the key roles and responsibilities involved in effective management of change

LO5 Identify the risks associated with management of change

LO6 Explain how the risks associated with management of change can be managed

Course code: MUK-036
Course type: E-learning course
Duration: 2 hours
Language: English
Price: GBP 125,-

Course Goal: This course aims to provide learners with an introduction to the principles of the equipment and technology associated with the bolting of flanged joints for pressurised systems. This course is intended to reflect industry ‘best practice’ for competence in relation to mechanical joint operations and applies to both the onshore and offshore Oil and Gas Industry.

 

Target Audience: This course is aimed at all personnel involved in mechanical joint operations, particularly those who are expected to undertake related duties in the workplace.

 

This course contains the following sections:

 

Section 1: An Introduction to Mechanical Joint Integrity

Section 2: Principles of Hand Torquing

Section 3: Principles of Hydraulic Tensioning

Section 4: Principles of Controlling Tightening

Course code: MTP-040
Course type: E-learning course
Duration: 45 minutes
Language: English, Norwegian
Price: GBP 120,-

The course looks at the purpose of the ISM code which is to maintain safety in international shipping, reduce pollution from vessels, protect the exterior environment and prevent injury or loss of human life.

The course covers the following subjects:

- What is the ISM code?
- Who does the ISM code apply to?
- Audits
- Applicable conventions and regulations
- The ISM code documented
- The ISM code in the management system
- The purpose of the ISM code
- Deviation management
- The ISM code structure
- The Master’s responsibility
- The Company’s responsibility
- Governing documentation
- Reporting and assessment of deviations
- Maintenance and certification

Course code: MUK-114
Course type: E-learning course
Duration: 1 hour
Language: English
Price: GBP 80,-

Course Goal: This course aims to provide Fire Wardens with an overview of the knowledge that they need to carry out their duties safely and effectively in line with industry best practice

 

Learning Objectives

 

LO1 Explain the responsibilities of employers and employees

LO2 Identify key fire safety legislative requirements

LO3 Recognise how to keep the workplace safe

LO4 Identify what should be considered during a fire safety risk assessment

LO5 Explain what to do upon hearing the fire alarm or upon discovering a fire

LO6 Identify the fire triangle and explain how it works

LO7 Identify typical ignition sources

LO8 Identify typical fuel sources

LO9 Explain how oxygen supports the fire triangle

LO10 Explain how fire spreads

LO11 Describe the dangers of smoke

LO12 Describe how to extinguish a fire

LO13 Give an overview of the different fire classifications

LO14 Explain what is meant by ‘flashpoint’ and ‘ignition temperature’

LO15 Describe different types of fire-fighting equipment

LO16 Describe the responsibilities of a Fire Warden

LO17 Identify different fire prevention measures

LO18 Explain the actions you should take in a fire situation

LO19 Identify key fire safety information and explain where it should be displayed

Course code: MUK-131
Course type: E-learning course
Duration: 15 Minutes
Language: English
Price: GBP 40,-

Course Goal: This course aims toprovide learners with an overview of the requirements for storing, transporting and handling explosives

 

Target Audience: All relevant personnel

 

Learning Objectives:

 

LO1 Explain why explosives are used in the Oil and Gas Industry

LO2 Identify the different types of explosives used in the Oil and Gas Industry

LO3 Give examples of hazards associated with the storage, transportation and handling of explosives

LO4 Explain the requirements for the transportation and labelling of explosives

LO5 Identify the mitigation measures designed to reduce the likelihood or consequences of an explosion

Hits per page
| 4 ... |