Course catalogue

Presentation

This training course provides general information on the ship’s propulsion system and its main components, the Rules’ requirements for design and survey of propeller and shaft installations, the requirements and methodology for the assessment on board of shaft alignment, and an overview of tailshaft survey requirements.

Objectives

On completion of the training, students will be able to:

Know the main propulsion shaft components

Understand the design requirements for propellers and propeller shafts 

Get familiar with the arrangements and installation on board of propellers and propeller shafts

Understand the main requirements for shaft alignment

Understand the survey requirements for propeller shafts and other propulsion systems.

Program

Main components of propulsion shafting

Design and construction of propulsion shafting

o Rules requirements

o Shaft alignment software

o Documentation to be submitted

o Materials

o Couplings

o Scantlings

o Lubrication system

Arrangement and installation – Shaft alignment

o Alignment calculation

o Shaft alignment sighting

o GAP and SAG method

o Bearing loads

o Alignment checking after chocking

Material tests, workshop inspections and testing, certification

Propellers

o Classification requirements

o Propeller types

o Geometry of propeller

o Materials

o CPP control system

o Arrangement and installation

o Testing and certification

Tailshaft surveys

o Survey schemes

o Periodicity

o Scope of surveys for traditional propeller shafts

o Scope of surveys for other propulsion systems

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Propeller and Shaft Installations, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Propeller and Shaft Installations is obtained after completion of the course and passing the online test.

Presentation

This training course provides a general overview of the MARPOL requirements concerning the protection against oil pollution from cargo spaces of oil tankers.

Objectives

On completion of the training, students will be able to:

Understand the MARPOL requirements for the prevention of oil pollution from cargo spaces of oil tankers.

Get familiar with the pollution prevention equipment required by the MARPOL Convention.

Know the requirements for survey and certification of oil tankers.

Program

Segregated ballast tanks

Double hull and double bottom

Pump-room bottom protection

Subdivision and stability

Slop tanks

Pumping, piping and discharge arrangements

Oil discharge monitoring and control system

Oil/water interface detector

Crude oil washing system

Control of discharge of oil

Oil record book part II

Ship-to-ship transfer

Survey and certification, type-approval certificates

Different survey types

Certificate

On completion of the training program, the student will be awarded:

A Certificate of MARPOL Oil Pollution from Cargo Spaces, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of MARPOL Oil Pollution from Cargo Spaces is obtained after completion of the course and passing the online test.

Presentation

This training course composed of 4 modules provides an overview of the Polar Code. It includes a general presentation of the Polar Code, the certification process, the safety requirements and the environmental protection requirements.

Objectives

On completion of the training, students will be able to:

Understand the main sources of hazards associated with the operations in polar waters and be familiar with the general principles, structure and philosophy of the Polar Code.

Know the main steps of the certification process, the operational assessment methodologies used to establish the operational limitations in ice operations, the requirements and contents of the Polar Water Operational Manual, and the survey and certification requirements.

Have a general understanding of the safety requirements concerning ship’s design and construction, machinery installations, safety equipment and fire protection, safety of navigation and communication equipment.

Get familiar with the requirements for operations in polar waters and training of crew.

Understand the Polar Code requirements for protection against oil pollution, NLS pollution, sewage pollution and garbage disposal.

Program

Module 1 – The Code

Introduction

Regulatory framework

The Polar Code

Module 2 – Certification Process

Certification overview

Operational assessment

Polar Water Operational Manual

Surveys and Certification

Polaris

BV Rules 

Module 3 – Safety Requirements

What does the Polar Code mean for safety?

Design and Construction

Equipment

Fire protection

Life-saving appliances

Operations and manning 

Module 4 – Environmental protection

How the Polar Code protects the environment?

Pollution prevention

Certificate

On completion of the training program, the student will be awarded: 

A Certificate of Polar Code, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Polar Code is obtained after completion of the course and passing the online test.

Presentation

This training course provides an overview of the different techniques employed for non-destructive tests (NDT) of materials and welding, their objectives and principles.

Objectives

On completion of the training, students will be able to:

Know the objectives and principles of the various non-destructive testing methods.

Differentiate NDT methods regarding application selection and physical principles.

Understand the evaluation process referred to the testing procedure.

Be familiar with the reliability of the various NDT methods.

Program

Definitions and terminology

Role of non-destructive testing

NDT methods

Systematisation of NDT methods

o Visual testing

o Penetrant testing

o Magnetic particles testing

o Radiographic testing

o Ultrasonic testing

Evaluation of NDT findings

Indications and flaws

Acceptance criteria

Reliability of NDT

Probability of detection

NDT operators certification

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Introduction to NDT, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Introduction to NDT is obtained after completion of the course and passing the online test.

Presentation

This training course provides a general overview of the requirements of the International Load Lines Convention and the conditions of assignment of load lines.

Objectives

On completion of the training, students will be able to:

Know the general requirements of the International Load Lines Convention and understand the conditions of assignment of load lines.

Know the different types of surveys; understand the scope of each survey and the certificates, records and documents associated with the Load Lines Convention.

Know the most common deficiencies and PSC detainable items in connection with the Load Lines Convention.

Program

History of Load Lines Convention

Purpose of the Convention

Definitions

Freeboard calculation

Load line marks

Conditions of assignment

o Information to be supplied to the Master

o Doors

o Cargo and other hatchways

o Machinery space openings and miscellaneous openings

o Ventilators and air pipes

o Scuppers, inlets and discharges

o Scuttles and windows

o Freeing ports

o Protection of crew

o Special conditions of assignment for Type A ships

Special requirements for ships assigned with timber freeboards

Certificates, records and other documents

Scope of Load Line surveys

o Initial survey

o Annual survey

o Renewal survey

Common PSC deficiencies related to Load Lines

o PSC statistics

o Detainable deficiencies

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Load Lines, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Load Lines is obtained after completion of the course and passing the online test.

The course is in accordance with NS-EN 1591-4 and undergoes the same course content as an ordinary four-day course but without the use of hydraulic torque tool and tensioning tools.

The use of a mechanical torque wrench is the main focus but also a review of procedures, flanges, gaskets, practical tasks and more.

The course ends with a theoretical and practical exam. If passed, the approval is valid for 5 years.

Courses are conducted in Stavanger or Bergen
and is carried out on request.

Course price NOK 5300, - pr. participant.

Kurset er i henhold til NS-EN- 1591-4. Kurset øker kompetansen og gir grunnleggende kunnskaper innen forberedelse, planlegging, utførelse og dokumentering av arbeid med boltetrekking av flensforbindelser på trykksatte systemer.

Kurset dekker følgende tabeller i NS-EN 1591-4:

Tabell 1: Foundation level training matrix.

Tabell 2: Training matrix for hydraulic tension tightening.

Tabell 3: Training matrix for hydraulic torque tightening.

Tabell 6: Training matrix for bolt load determination after assembly.

Tabell 7: Training matrix for compact flanges.

Tabell 8: Training matrix for clamp connectors

Tabell 9: Training matrix for special connector/flanges

Hensikt: Hensikten med kurset å forhindre skade på personell, miljø og utstyr. Dette kan forebygges ved å styrke kompetansen og øke forståelsen hos den enkelte.

This course is only available in Norwegian.

Hensikt: Grunnleggende overlevelsestrening for offshore vindindustri. 

Ved gjennomføring av Global Wind Organization (GWO) Basic Safety Training (BST) vil delegatene ha en bevissthet om farene som oppstår når de arbeider i vind-industrien og hvordan man kontrollerer og reduserer disse farene.

Kursdeltakerne vil få (repetert) kunnskap og ferdigheter til å anerkjenne fordeler og begrensninger knyttet til livreddende utstyr og PVU samt korrekt bruk av dette i forbindelse med offshore vind. 

Hensikten med kurset er å gi deltakerne kunnskaper/oppfriskning om livreddende utstyr, GMDSS og SAR utstyr, hvordan en kollektivt kan øke sjansen til overlevelse i en nødsituasjon, hvordan entre og forlate vindturbiner, samt evakuering i nødsituasjoner. 

Kurset dekker krav til opplæring av personell og repetisjonskurs både land- og havvind iht:

- Global Wind Organization (GWO)

- Arbeidstilsynet (Forskrifter)


Kompetanse for «Sea Survival» skal vedlikeholdes iht. retningslinje i GWO standarden. Det skal gjennomføres repetisjonskurs hvert 2. år.

This course is only available in Norwegian.

LEARNING OBJECTIVES

The period of supervised DP sea time days after the Simulator Course may be reduced by a maximum of 30 days by the satisfactory completion of an intensive DP Simulator Course.

CONTENT

• Study of DP incidents
• Construction and use of worksite diagrams, Electronic Charts and Vessel templates for use in DP operations
• Preparation of plans for a projected DP operation,contingency plans for expected deviations and emergencies
• Participation in simulated situations in a variety of DP operations while handling routine and emergency situations
• Risk and safety analysis, and defining DP equipmentclasses
• The DP system’s utilization of position

LEARNING PROCESS

The participants will work with practical scenarios based on real operations, training on planning and executing specified operations under varying simulated conditions.

During the operations, typical DP failure modes will be included. Communication with field control, other vessels and the different departments onboard will be included. A rotation plan will be made for participants to act in different roles during the course.

The scenarios will be run on a K-POS DP system Class2, in a full mission simulator environment connected to an advanced simulator control (NI Class A).

SPECIAL INFORMATION

The Sea Time Reduction Course reduces phase D of the Nautical Institute (NI) DP Operator Certification Scheme (watchkeeping experience). The course will be logged into the Nautical Institute DP Operator’s log book and reduce the Watchkeeping Experience requirements by 30 days

CERTIFICATE

Certification of attendance will be issued on succcessful completion of the course.

LEARNING OBJECTIVES

By the end of the course the participants should:

• Have acquired knowledge of the latest rules and regulations
• Have acquired knowledge of the latest developments within sensors and Position Reference Systems (PRS)
• Have acquired knowledge of the latest relevant DP incidents and why they occurred
• Be able to recognize the various alarm, warning and information messages
• Carry out operational planning, risk assessment and hazard identification tasks
• Set up the DP system for a particular task/ operation
• Decide on courses of action because of system failure

CONTENT

The course is conducted as classroom training, combining theoretical presentation (Show-and Tell Lessons) and practical work/discussion with exercises in simulator and guidance (Stair-Step learning design). For practical capabilities and skills, exercises are performed in full equipped DP simulator. This course will fulfil the revalidation learning objectives as specified by Nautical institute.

SPECIAL INFORMATION

At present (2016), the requiremets is that the holder of a Nautical Institute (NI) DPO certificate must revalidate their DPO certificates.

The requirement is that the DPO must have at least 150 days of DP sea time experience in the previous 5 years, if not NI DPO Revalidation course is needed.

CERTIFICATE

A certificate acceditated by the Nautical Institute will be issued on succcessful completion of the course.

LEARNING OBJECTIVES

After the course the participant is able to:
• Operate the system
• Understand the basic principles of stability
• Safe vessel operation and utilization of load capacity

CONTENT

Themes in the course are:
• Basic stability theory
• System setup and configuration
• Basic operation and understanding of the system
• Intact stability and utilization of vessel capacity
• Damage stability with emergency response

LEARNING PROCESS

The training will be a combination of theoretical lessons and practical exercises. Each participant will use a PC with necessary software installed to do training cases. 

SPECIAL INFORMATION

This course is done on a demo ship with a generic software.

CERTIFICATE

Certificate of attendance will be issued upon completion of the course.

LEARNING OBJECTIVES

After the course, the successful participants are able to:

• Define the principles of DP
• Recognise the component parts of a DP system
• Understand the relationship between vessel movement  position reference systems, sensors, computers propulsion units and feedback
• Understand the concept of redundancy
• Understand the DP modes of control
• Describe the operation of sensors and common position reference systems
• Describe propulsion units, types and configurations
• Understand power supply, redundancy and management
• Practice communication and watch handover procedures

CONTENT

• Definition of DP, elements of the DP system, DP systems redundancy, and Class Requirements
• Functions of the DP system, and DP principles
• Different types of DP vessels and DP operations, sensors and use of sensor inputs
• Introduction to position reference systems and the DP system’s use of position measurements
• Vessel capability, DP consequence analysis and DP capability analysis
• Thrusters and manoeuvring systems
• Power systems and Blackout Prevention
• Operational procedures for DP operation, and procedures for operating the DP system
• Study of DP incidents
• Principal use of the DP system

LEARNING PROCESS

The training will be a combination of theoretical lessons and practical exercises. During the course each participant will have his own operator station with generic DP software.

SPECIAL INFORMATION

The DP Induction course is the first phase of the Nautical Institute (NI) DP Operator Certification Scheme. The course participants will be issued with the NI Dynamic Positioning Operator’s Log Book upon successful completion of the DP Induction Course.

This course is according to the system specific competence requirements in IMO STCW Regulations I/14 1.5, Part A-I/14 2.1.1, part B V/f 6 and IMCA M117.

CERTIFICATE

A certificate accreditated by the Nautical Institute will be issued on succcessful completion of the course.

LEARNING OBJECTIVES

This course aim to improve the participants knowledge, understanding and skills in the following overall learning objective(s):
• Obtain competence of forces involved, related to ship handling in general, and offshore loading in particular
• Obtain competence of planning and manual maneuvering in port, narrow waters and at offshore loading installations
• Obtain competence of the Equinor, Teekay and OGUK’s requirements for training of shuttle tanker personnel
• Improve skills in performing good Bridge Team Cooperation and communication
• Improve competence in use of all propulsion machinery, navigational equipment, steering systems and deck equipment involved

CONTENT

The course content aim to give the participants basic knowledge, understanding and skills of: • Ship handling
• Pivot point
• Propellers/rudders
• Thrusters
• Anchoring
• Waves/currents
• Tugs
• Squat/sink age/interaction
• ROT technique

LEARNING PROCESS

The course is divided into modules and consists of totally nine theoretical lessons and eight selected simulator exercises. Participant learning progress is assessed by concurrent evaluation of it during both theory sessions and simulator exercises.

CERTIFICATE

Certification of attendance will be issued on successful completion of the course.

LEARNING OBJECTIVES

This course is specifically designed for training future DPO’s on board a large number of offshore vessels.

The course aim to provide the candidates with knowledge and skills as preparation for DNV DPO Advanced Operations exams and certification.

By the end of course the students shall have:

• Acquired a thorough knowledge of the various types of DP operations such as ROV operations, cable laying pipe laying, trenching, dredging and rock-dumping
• The capability to operate the DP in the various modes associated with such operations, i.e. joystick,  auto pos mode, autotrack mode and follow target mode
• Recognize when environmental conditions or system failure  requires DPO to take action to avoid hazardous situations
• The  ability to carry out such operations according to existing operational guidelines and checklists
• The ability  to demonstrate good personal attitudes towards safety in operating DP vessels according to best practice in the industry

CONTENT

Planning,  briefing and de-briefing of various field exercises according to the existing guidelines, regulations, and industry standards. Repetition of necessary DP theory to close any knowledge gap the students may have in these subjects.

LEARNING PROCESS

All DP  exercises will be carried out on a full scale DNV GL Approved DP Class A simulator, using vessels that are equipped according to DP class 2 and 3. The participants will perform both surface and subsea  operations, utilizing the following DP modes: Joystick, Autoposition, Autotrack and Follow target functionalities.

SPECIAL INFORMATION

• DNV GL, Standard for Certification no. 0023
• DNV GL, Standard for Certification no. 0008
• DNV GL, RP-0007
• NMA 201209765-4/813.4.
• GOMO, Guidelines for offshore marine operations, Supply and Rig Move Operations and other relevant guidelines such as IMCA M-117 and other IMCA guidelines

A level test will be conducted before commencing the course.

CERTIFICATE

Certification of attendance will be issued upon successful completion of the course.

Når kurset er fullført, skal deltakerene være i stand til å klargjøre livbåten, organisere ombordstigning, låre og frigjøre båten, manøvrere og lede operasjonen av livbåten på vannet. 

Regelverk / ansvarsforhold 

Utsetning- systemer for skip og rigg 

Nødkommunikasjon og aktuelt utstyr 

Utstyr i båt og flåte 

Livreddende førstehjelp 

Prosedyrer / alarminstruks 

Kommandoforhold / samarbeid 

Personlig vern og utstyr 

Praktisk øvelse under aktuelle båttype 

Opphold i båt 

Berge opp folk fra sjøen 

Snu en kantret redningsflåte iført redningsvest

Førstehjelp

With COVID-19 meaning that home working is no longer an option but a necessity for many, what are the potential side effects on our health and work performance. Employers may need to provide additional training to ensure appropriate supervision and work behaviours. These include remote technology, communication skills development, time management and ergonomics.

Effective remote working requires greater self-control and discipline to avoid the boundaries between work and personal life becoming blurred. Research has shown that, in general, homeworkers tend to work longer than office workers and this increases with the use of technology. Homeworkers do benefit from greater working time autonomy, but how effectively this is applied depends on the discipline of the individual.

The ‘Effective Remote Working’ bundle includes 3 months access to 10 online courses and over 7 hours of eLearning.  

• Management of Change

• Lone Working (Employees)

• Smart Workplaces: Responsible Social Media for Team members

• Business Writing: E-Mail Techniques

• AEC Success: Effective Decision Making

• Webinars – Conducting a Web-based Presentation

• ABCs of Managing Time & Effort: The 80/20 Way

• Smart Time Management: 7 Steps to Regaining Control of Your Day

• 3-way Communication

• Smart Customer Service 3: Effective Verbal and Nonverbal Communication

Presentation

This training course provides an overview of the Ultrasonic Testing (UT) method for non-destructive examination of materials and welding, its objectives and principles.

Objectives

On completion of the training, students will be able to:

Understand the basic physical principles of ultrasonic testing.

Know the testing procedure and the inspection process referred to the equipment used.

Differentiate applications and the acceptance criteria applied.

Get familiar with the purpose of calibration and reference blocks to ensure the quality of test performance and test results.

Program

Basic principle

o Ultrasonic waves and propagation

o Ultrasonic pulse-echo principle

Equipment and testing materials

o Ultrasonic testing instruments

o Ultrasonic testing probes

o Coupling media

o Calibration and reference blocks

Testing procedure

o Surface preparation

o Scanning – ultrasonic testing techniques

o Testing parameters

o Examination

o Data presentation

Applications and acceptance criteria

o Scope

o Indication evaluation

o Acceptance criteria

o Test report

Reliability, quality of test results

o UT system performance

o NDT personnel competence

Certificate

On completion of the training program, the student will be awarded:

A Certificate of NDT – Ultrasonic Testing, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of NDT – Ultrasonic Testing is obtained after completion of the course and passing the online test.

Presentation

This training course provides a general introduction to welding, including an introduction to metallurgy, general information concerning welding, an overview of the electric arc processes commonly used in shipbuilding and details of welding inspection.

Objectives

On completion of the training, students will be able to:

Understand the nature and know the mechanical properties of metals; Understand the production process of steel and aluminium and the application of casting and forging processes.

Understand fundaments of fusion welding; Know how to determine heat input and preheat temperature; Understand the influence of the thermal cycle on weld microstructure and distortion; Know the general types of welding joints and the different welding positions

Know how to differ and recognize the arc welding processes used in shipbuilding; Understand the applicability and limitations of the different welding processes; Get familiar with common types of arc welding equipment and power sources

Know and apply the required activities in welding inspection; Determine and arrange the scope of inspection plan for different tasks; Know the different types of weld imperfections; Understand how to perform visual inspection of welding

Program

Module 1 – Introduction to Metallurgy

Module 2 – Welding Fundamentals

Module 3 – Arc Welding Processes

Module 4 - Welding Inspection

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Welding Fundamentals, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Welding Fundamentals is obtained after completing the course and passing the online test.

Presentation

This training course provides an overview of the Penetrant Testing (PT) method for non-destructive examination of materials and welding, its objectives and principles.

Objectives

On completion of the training, students will be able to:

Understand the basic physical principles of liquid penetrant testing.

Know the testing procedure and the inspection process referred to testing materials and equipment.

Differentiate applications and the acceptance criteria applied.

Get familiar with the purposes of reference materials and/or blocks to ensure the quality of test performance and testing results.Program

Basic principle, capillary effect

Physical properties of the penetrant

Testing procedure

o Pre-cleaning

o Penetrant application

o Excess penetrant removal

o Developer application

o Inspection and recording

o Post-cleaning

Testing materials and equipment

o Penetrants

o Removal methods

o Developers

o Equipment

Applications and acceptance criteria

o Indications

o Test report

Reliability, quality of test performance

o Surface preparation and condition

o Types of penetrant materials and equipment used

o Penetrations and development time

o Viewing conditions

o The temperature of the test surface

o The material tested and flaws expected

o NDT personnel competence

o Safety issues

Certificate

On completion of the training program, the student will be awarded:

A Certificate of NDT – Penetrant Testing, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of NDT – Penetrant Testing is obtained after completion of the course and passing the online test.

Presentation

This training course provides a general introduction to ship machinery, details of diesel engines, a description of piping systems in ship's engine rooms and an overview of marine auxiliary machinery such as pumps, compressors, purifiers, heat exchangers, etc.

Objectives

On completion of the training, students will be able to:

Know the different types and arrangements of ship machinery applied for ship propulsion, understand the main parameters of ship machinery and the basic propulsion power transmission principles, and know the conceptual requirements for reliable and safe work of ship propulsion.

Know the main parts of marine diesel engines and understand their functions, get familiar with the most common problems involving engine parts, and understand the basic requirements for the reliable and safe operation of diesel engines.

Know the different types of piping systems in the ships engine room, understand the purpose and the basic arrangement of systems.

Know the different types of auxiliary machinery found on board ships, understand their working principles and the basic requirements for reliable and safe work of auxiliary machinery.

Program

Module 1 – Ship Machinery

Overview of the different propulsion types: Low-speed diesel engine layout, medium-speed diesel engine layout, steam propulsion with HP and LP steam turbines, gas turbines propulsion, diesel-electric propulsion, combined layouts, dual fuel engines, nuclear propulsion plants

Diesel engines outline

High pressure and low-pressure steam turbines 

Gas turbine cycles

Module 2 – Engine Details

Cylinder heads

Cylinder liners

Pistons

Crosshead and connecting rods

Bearings

Crankshaft

Engine casing

Turbocharger

Module 3 – Engine Room Systems

Seawater system

Freshwater system

Fuel oil system

Lubricating oil system

Compressed air system

Exhaust system

Module 4 – Marine Auxiliary Machinery

Pumps: Centrifugal pumps, positive displacement pumps, reciprocating pumps

Separators

Heat exchangers

Air compressors and air receivers

Steering gear

Reduction gears

Shaft generator

Thrust bearing

Controllable pitch propeller

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Marine Engineering Fundamentals, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Marine Engineering Fundamentals is obtained after completing the course and passing the online test.