Course catalogue

LEARNING OBJECTIVES

After the course the participant is able to:
• Operate the system
• Understand the basic principles of stability
• Safe vessel operation and utilization of load capacity

CONTENT

Themes in the course are:
• Basic stability theory
• System setup and configuration
• Basic operation and understanding of the system
• Intact stability and utilization of vessel capacity
• Damage stability with emergency response

LEARNING PROCESS

The training will be a combination of theoretical lessons and practical exercises. Each participant will use a PC with necessary software installed to do training cases. 

SPECIAL INFORMATION

This course is done on a demo ship with a generic software.

CERTIFICATE

Certificate of attendance will be issued upon completion of the course.

LEARNING OBJECTIVES

This course is specifically designed for training future DPO’s on board a large number of offshore vessels.

The course aim to provide the candidates with knowledge and skills as preparation for DNV DPO Advanced Operations exams and certification.

By the end of course the students shall have:

• Acquired a thorough knowledge of the various types of DP operations such as ROV operations, cable laying pipe laying, trenching, dredging and rock-dumping
• The capability to operate the DP in the various modes associated with such operations, i.e. joystick,  auto pos mode, autotrack mode and follow target mode
• Recognize when environmental conditions or system failure  requires DPO to take action to avoid hazardous situations
• The  ability to carry out such operations according to existing operational guidelines and checklists
• The ability  to demonstrate good personal attitudes towards safety in operating DP vessels according to best practice in the industry

CONTENT

Planning,  briefing and de-briefing of various field exercises according to the existing guidelines, regulations, and industry standards. Repetition of necessary DP theory to close any knowledge gap the students may have in these subjects.

LEARNING PROCESS

All DP  exercises will be carried out on a full scale DNV GL Approved DP Class A simulator, using vessels that are equipped according to DP class 2 and 3. The participants will perform both surface and subsea  operations, utilizing the following DP modes: Joystick, Autoposition, Autotrack and Follow target functionalities.

SPECIAL INFORMATION

• DNV GL, Standard for Certification no. 0023
• DNV GL, Standard for Certification no. 0008
• DNV GL, RP-0007
• NMA 201209765-4/813.4.
• GOMO, Guidelines for offshore marine operations, Supply and Rig Move Operations and other relevant guidelines such as IMCA M-117 and other IMCA guidelines

A level test will be conducted before commencing the course.

CERTIFICATE

Certification of attendance will be issued upon successful completion of the course.

LEARNING OBJECTIVES

This course aim to improve the participants knowledge, understanding and skills in the following overall learning objective(s):
• Obtain competence of forces involved, related to ship handling in general, and offshore loading in particular
• Obtain competence of planning and manual maneuvering in port, narrow waters and at offshore loading installations
• Obtain competence of the Equinor, Teekay and OGUK’s requirements for training of shuttle tanker personnel
• Improve skills in performing good Bridge Team Cooperation and communication
• Improve competence in use of all propulsion machinery, navigational equipment, steering systems and deck equipment involved

CONTENT

The course content aim to give the participants basic knowledge, understanding and skills of: • Ship handling
• Pivot point
• Propellers/rudders
• Thrusters
• Anchoring
• Waves/currents
• Tugs
• Squat/sink age/interaction
• ROT technique

LEARNING PROCESS

The course is divided into modules and consists of totally nine theoretical lessons and eight selected simulator exercises. Participant learning progress is assessed by concurrent evaluation of it during both theory sessions and simulator exercises.

CERTIFICATE

Certification of attendance will be issued on successful completion of the course.

LEARNING OBJECTIVES

After the course, the successful participants are able to:

• Define the principles of DP
• Recognise the component parts of a DP system
• Understand the relationship between vessel movement  position reference systems, sensors, computers propulsion units and feedback
• Understand the concept of redundancy
• Understand the DP modes of control
• Describe the operation of sensors and common position reference systems
• Describe propulsion units, types and configurations
• Understand power supply, redundancy and management
• Practice communication and watch handover procedures

CONTENT

• Definition of DP, elements of the DP system, DP systems redundancy, and Class Requirements
• Functions of the DP system, and DP principles
• Different types of DP vessels and DP operations, sensors and use of sensor inputs
• Introduction to position reference systems and the DP system’s use of position measurements
• Vessel capability, DP consequence analysis and DP capability analysis
• Thrusters and manoeuvring systems
• Power systems and Blackout Prevention
• Operational procedures for DP operation, and procedures for operating the DP system
• Study of DP incidents
• Principal use of the DP system

LEARNING PROCESS

The training will be a combination of theoretical lessons and practical exercises. During the course each participant will have his own operator station with generic DP software.

SPECIAL INFORMATION

The DP Induction course is the first phase of the Nautical Institute (NI) DP Operator Certification Scheme. The course participants will be issued with the NI Dynamic Positioning Operator’s Log Book upon successful completion of the DP Induction Course.

This course is according to the system specific competence requirements in IMO STCW Regulations I/14 1.5, Part A-I/14 2.1.1, part B V/f 6 and IMCA M117.

CERTIFICATE

A certificate accreditated by the Nautical Institute will be issued on succcessful completion of the course.

Presentation

This training course provides an overview of the Ultrasonic Testing (UT) method for non-destructive examination of materials and welding, its objectives and principles.

Objectives

On completion of the training, students will be able to:

Understand the basic physical principles of ultrasonic testing.

Know the testing procedure and the inspection process referred to the equipment used.

Differentiate applications and the acceptance criteria applied.

Get familiar with the purpose of calibration and reference blocks to ensure the quality of test performance and test results.

Program

Basic principle

o Ultrasonic waves and propagation

o Ultrasonic pulse-echo principle

Equipment and testing materials

o Ultrasonic testing instruments

o Ultrasonic testing probes

o Coupling media

o Calibration and reference blocks

Testing procedure

o Surface preparation

o Scanning – ultrasonic testing techniques

o Testing parameters

o Examination

o Data presentation

Applications and acceptance criteria

o Scope

o Indication evaluation

o Acceptance criteria

o Test report

Reliability, quality of test results

o UT system performance

o NDT personnel competence

Certificate

On completion of the training program, the student will be awarded:

A Certificate of NDT – Ultrasonic Testing, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of NDT – Ultrasonic Testing is obtained after completion of the course and passing the online test.

Presentation

This training course provides a general introduction to ship machinery, details of diesel engines, a description of piping systems in ship's engine rooms and an overview of marine auxiliary machinery such as pumps, compressors, purifiers, heat exchangers, etc.

Objectives

On completion of the training, students will be able to:

Know the different types and arrangements of ship machinery applied for ship propulsion, understand the main parameters of ship machinery and the basic propulsion power transmission principles, and know the conceptual requirements for reliable and safe work of ship propulsion.

Know the main parts of marine diesel engines and understand their functions, get familiar with the most common problems involving engine parts, and understand the basic requirements for the reliable and safe operation of diesel engines.

Know the different types of piping systems in the ships engine room, understand the purpose and the basic arrangement of systems.

Know the different types of auxiliary machinery found on board ships, understand their working principles and the basic requirements for reliable and safe work of auxiliary machinery.

Program

Module 1 – Ship Machinery

Overview of the different propulsion types: Low-speed diesel engine layout, medium-speed diesel engine layout, steam propulsion with HP and LP steam turbines, gas turbines propulsion, diesel-electric propulsion, combined layouts, dual fuel engines, nuclear propulsion plants

Diesel engines outline

High pressure and low-pressure steam turbines 

Gas turbine cycles

Module 2 – Engine Details

Cylinder heads

Cylinder liners

Pistons

Crosshead and connecting rods

Bearings

Crankshaft

Engine casing

Turbocharger

Module 3 – Engine Room Systems

Seawater system

Freshwater system

Fuel oil system

Lubricating oil system

Compressed air system

Exhaust system

Module 4 – Marine Auxiliary Machinery

Pumps: Centrifugal pumps, positive displacement pumps, reciprocating pumps

Separators

Heat exchangers

Air compressors and air receivers

Steering gear

Reduction gears

Shaft generator

Thrust bearing

Controllable pitch propeller

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Marine Engineering Fundamentals, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Marine Engineering Fundamentals is obtained after completing the course and passing the online test.

Presentation

This training course provides an overview of the Penetrant Testing (PT) method for non-destructive examination of materials and welding, its objectives and principles.

Objectives

On completion of the training, students will be able to:

Understand the basic physical principles of liquid penetrant testing.

Know the testing procedure and the inspection process referred to testing materials and equipment.

Differentiate applications and the acceptance criteria applied.

Get familiar with the purposes of reference materials and/or blocks to ensure the quality of test performance and testing results.Program

Basic principle, capillary effect

Physical properties of the penetrant

Testing procedure

o Pre-cleaning

o Penetrant application

o Excess penetrant removal

o Developer application

o Inspection and recording

o Post-cleaning

Testing materials and equipment

o Penetrants

o Removal methods

o Developers

o Equipment

Applications and acceptance criteria

o Indications

o Test report

Reliability, quality of test performance

o Surface preparation and condition

o Types of penetrant materials and equipment used

o Penetrations and development time

o Viewing conditions

o The temperature of the test surface

o The material tested and flaws expected

o NDT personnel competence

o Safety issues

Certificate

On completion of the training program, the student will be awarded:

A Certificate of NDT – Penetrant Testing, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of NDT – Penetrant Testing is obtained after completion of the course and passing the online test.

Hensikt:

Målsetting med opplæring er at den som gis opplæring tilegner seg tilstrekkelig kunnskap om metoder for å lede og veilede løfteoperasjoner slik at de blir forskriftmessig utført.

Opplæringen gir også kunnskap om farer forbundet med løfteoperasjoner samt bruk av risikokartlegging.

Kurset gir deltakere kunnskap til å kunne utøve overordnet operasjonell ledelse av løfteoperasjoner. Med det menes å kunne planlegge, risikokartlegge og evaluere, samt forebygge ulykker. Videre vil deltaker også tilegne seg kunnskaper om å gjøre rede for materialhåndteringsplan, oppbevaring og bruk av utstyr.

Målsetting med opplæring er at den som gis opplæring tilegner seg tilstrekkelig kunnskap om metoder for å lede og veilede løfteoperasjoner slik at de blir forskriftmessig utført.

Innhold:

• Krav og ansvar til rollen operasjonelt ansvarlig

• Lover, forskrifter, standarder og retningslinjer som gjelder vedr. bruk av løfteutstyr

• Overordnet operasjonell ledelse av løfteoperasjoner

• Helhetlig planlegging av løfteoperasjoner

• Risikokartlegging

• Identifisering av og etablering av barrierer. Gjennomføring og evaluering av en løfteoperasjon

• Informasjonsutveksling

• Krav for oppbevaring av løst løfteutstyr

• Krav for ulike typer løfteutstyr

• Krav til fadder, praksis og sensor

• Avsluttende prøve

Presentation

This training course provides a general introduction to welding, including an introduction to metallurgy, general information concerning welding, an overview of the electric arc processes commonly used in shipbuilding and details of welding inspection.

Objectives

On completion of the training, students will be able to:

Understand the nature and know the mechanical properties of metals; Understand the production process of steel and aluminium and the application of casting and forging processes.

Understand fundaments of fusion welding; Know how to determine heat input and preheat temperature; Understand the influence of the thermal cycle on weld microstructure and distortion; Know the general types of welding joints and the different welding positions

Know how to differ and recognize the arc welding processes used in shipbuilding; Understand the applicability and limitations of the different welding processes; Get familiar with common types of arc welding equipment and power sources

Know and apply the required activities in welding inspection; Determine and arrange the scope of inspection plan for different tasks; Know the different types of weld imperfections; Understand how to perform visual inspection of welding

Program

Module 1 – Introduction to Metallurgy

Module 2 – Welding Fundamentals

Module 3 – Arc Welding Processes

Module 4 - Welding Inspection

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Welding Fundamentals, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Welding Fundamentals is obtained after completing the course and passing the online test.

"“The single biggest problem in communication is the illusion that it has taken place.” 

-George Bernard Shaw 

Thanks to technology, we now have numerous ways to communicate with one another. Organizations depend on social media, texting, and tweeting in addition to emails to present themselves to all the stakeholders. These rapid-fire methods of communicating have changed how we speak, how we receive information, and how we interpret the information we’ve received. Sometimes, these speed-of-light methods of connecting can affect our communication skills. Have you ever wondered if the receiver received your communication correctly or not? Do you evaluate the messages you send? This course will help you with tricks to communicate effectively using electronic media.

• Judge whether your message is essential and timely 

• Draft short messages 

• Use tools and white spaces for flawless messages 

• Convey the gist of the message in the subject line 

• Make decisions on when to not send emails and when to reply promptly

Employees working in an organization bring a level of enthusiasm and energy to the work they do in the organization. They are committed and creative in their approach. This energy is crucial for any organizational success, and it is termed as emotional motivation. The factors influencing this energy level can be either intrinsic or extrinsic. In this lesson, you will learn about both intrinsic motivation and extrinsic motivation and how to leverage them. 

How do you motivate your team to do their best? You give them the tools, trust, and time to make their jobs personal. You provide enough challenge for them to work at facilitating better, but not so hard that they become discouraged. Help them connect with their work and give them a reason to work, which is beyond the paycheck. 

• Explain the challenges of using extrinsic motivation 

• Learn the three methods of intrinsic motivation: autonomy, mastery, and purpose

To better understand today’s digital age, it’s important to look back at the Industrial Revolution. As Steve Jobs said, “You can’t connect the dots looking forward, you can only connect them looking backward.” Just as the steam engine and other machines transformed the 18th-century economy, digital technologies are changing our world economy, business practices, customer expectations, and societal norms—and will continue to do so for the foreseeable future. And while it’s impossible to predict the exact changes that lie ahead, it’s possible to predict who will succeed: agile organizations who are able to quickly take advantage of new opportunities by applying digital technologies.

• Understand the parallels between the industrial revolution and the digital revolution

• Define Digital Transformation

• Understand how digital is changing the operation of businesses, affecting all business sectors, and is making organizations flatter

Do you want to mentor an environment of innovative thinking in your organization? A leader needs to have some qualities to promote innovative thinking among their team members. The leader also needs to know the techniques of exercising innovation. This lesson outlines the qualities and techniques as well as the four-step process of leading innovation sessions. You can also learn various strategies to maintain the environment of innovation in your organization. It encourages you to challenge your processes and think out of the box. This is a must-learn lesson for persons who want to lead innovation teams effectively.

• Describe an ideal change leader and team members

• Explain the techniques of exercising innovation

• Describe the four-step process of leading innovation sessions

Only in Norwegian

Kurset dokumenterer at skipsoffiserer (dekk og maskin) har gjennomført godkjent oppdateringskurs (IMO80) minst hvert femte år.

Deltakerne skal etter endt kurs kunne

- Ta kommandoen over en redningsfarkost eller mann-overbord-båt under og etter utsetting (Tabell VI/2-1) 
- Lede brannslokningsoperasjoner om bord på skip (Tabell VI/3) 
- Gi førstehjelp omgående i tilfelle av ulykke eller sykdom om bord (Tabell VI/4-1) 
- Gi medisinsk behandling av syke og skadde mens de er om bord. Delta i samordnede opplegg for medisinsk bistand til skip (Tabell VI/4-2)

Kursinnhold
- Medisinsk førstehjelp for maskinoffiserer
- Medisinsk behandling for dekksoffiserer
- Ledelse av brannslokking
- Bruk av redningsfarkoster

Praktiske øvelser

- Dag 1: Medisinsk behandling for dekksoffiserer

- Dag 1: Medisinsk førstehjelp for maskinoffiserer
- Dag 2: Brannledelsesteori, brannøvelser og røykdykking med pressluftapparater
- Dag 3: Redningsteori og mønstring og redningsøvelser med redningsfarkoster

Objective: Through a combination of theory and practical training, this course provides participants with the necessary knowledge and skills required to work safely in enclosed spaces.

The Norwegian Labor Inspection Authority has made major changes to the regulations. People who work in tanks and closed rooms are the biggest difference that the regulation "Work in tanks" has fallen away. This is replaced by section 29 of the regulations «execution of work», which states that all work in closed rooms shall be performed «without danger to life or health». A simple requirement that gives the employer a great deal of responsibility.

New SOLAS requirements: Exercises in closed rooms and rescue, as well as portable gas measuring equipment.

Applies to: All ships covered by SOLAS and all high-speed vessels, mobile offshore drilling units and dynamically positioned vessels

Our courses are in accordance with SOLAS-IMO requirements and the Norwegian Labor Inspection Authority - Execution of work

The definitions of a cramped space vary from country to country, but the usual criteria usually include:

- A room that is predominantly or completely closed
- Contains health and / or safety hazards
- Is not designed for continuous stay of employees
- Has entrances or exits that are small or difficult to access
- A room that is large enough that you can enter it completely and perform the work tasks you have been assigned
- Limited air circulation

Content:

- Review of public laws and regulations
- Know which constituents a safe breathing air contains
- How to make a gas measurement before entering
- Plan entry jobs and rescue operations in closed rooms
- Equipment knowledge
- Exercises in our training tank. We practice entry and use of fall protection equipment, rescue equipment, breathing air equipment and gas meter

A dream doesn't become reality through magic; it takes sweat, determination and hard work.

 -Colin Powell 

A new methodology for innovation, “Trystorming” is a combination of “Brainstorming” and “Trying” something practically. This lesson highlights the difference between brainstorming and trystorming, and provides the guidelines for where and when it can be used. Trystorming is a practical approach to innovating by focusing on practically trying or experimenting within reasonable limits to understand the efficacy of an idea before implementing it fully. Take this lesson to pick up the basics of trystorming and lead innovations in your organization.

• Explain what is trystorming 

• Know the difference between trystorming and brainstorming 

• Describe the guidelines for trystorming and where it can be used

The virtual interview can be a challenging and difficult process if you don’t prepare properly. You may face many challenges, such as technological, ambience related issues. However, to convene a successful interview, it is important to how to overcome these challenges. Branding your company is also one the challenges you may face when conducting virtual interview. Home setup throws various set of challenges, which one must overcome to have successful virtual interview. In this course, you will learn to overcome the challenges faced in conducting a successful virtual interview. 

• Identify the requisites of a pre-interview process

• List best practices while conducting interview virtually

• Identify post interview actionable

How much time do you spend developing your leadership succession plan? As older leaders begin to retire at greater rates, the 2018 Deloitte Millennial Survey discovered that 65% of potential millennial leaders feel unprepared to take their places. Forbes reports that by 2025, 75% of the workforce will be made up of millennials. These statistics suggest that there’s a leadership crisis on the horizon. Designing a strategy and framework to direct leadership development is mission critical for every organization. Training—and retaining —emerging leaders in your company should be a top priority. Understanding what team members want and expect from an employer will help you develop the right programs and systems to keep your talent engaged in learning, growing, and contributing to your organization.

• Retain your talented resource   

• Design a leadership development framework   

• Create a culture of learning

LEARNING OBJECTIVES

This course aim to provide Navigators on Shuttle Tankers knowledge and skills to be a certified DPO in offshore Loading Operations.

By the end of the course the students should have:

• Acquired a thorough knowledge of the various type of Offloading Operations, i.e. OLS (Offshore Loading System), SAL (Single Anchor Loading), Tandem loading from FPSO’s and FSU’s and DSL (Direct Shuttle Loading)
• The capability to operate the DP System in various
• modes associated with offshore loading operations; i.e. Joystick, Auto Pos, Approach, Weather Wane
• The ability to carry out any Offshore Loading Operation according to field procedures, guidelines and to best practice.
• The ability to react correctly to any unforeseen DP incident in order to avoid a disaster

CONTENT

• Simulator exercises
• Briefing and de-briefing of a variety of relevant exercises according to the actual field procedures
• Shuttle Tanker competence and training requirements
• Basic Human Factors

LEARNING PROCESS

All Offshore Loading exercises will be carried out on a Full Scale Visual DNV GL Approved DP Class A simulator, being able to simulate all types of operation listed as learning objectives.

SPECIAL INFORMATION

References:
• DNV GL, Standard for Certification no. 0023
• DNV GL, Standard for Certification no. 0008
• DNV GL, RP-0007

CERTIFICATE

Certification of attendance will be issued upon successful completion of the course.

LEARNING OBJECTIVES

The course aim to give knowledge, understanding and practical skills within:
• Operations
• Forces
• Communication
• Planning

CONTENT

• Safety functions
• Start / stop procedures
• Operational limitations of crane operations
• Communication during crane operations
• Preparation and planning of crane operations
• Internal transport on the installation
• Loading and unloading supply vessels
• Crane operation on various fixed and floating installations

LEARNING PROCESS

The purpose of this course is to give operators and others involved in lifting operations the basic knowledge, understanding and skills.

This is achieved through an in-depth period of training on a full-scale DNV GL Class A crane simulator, supported by a program of lectures and instruction.

Study will cover dierent types of loads and external forces affecting the load on crane and boat.

SPECIAL INFORMATION

References: NORSOK R003

The course can be adjusted to suit company specific needs regarding the choice of unloading/loading procedures.

CERTIFICATE

Certification of attendance will be issued upon successful completion of the course.